All times are UTC-06:00




Post new topic  Reply to topic  [ 12 posts ] 
Author Message
PostPosted: Sun Nov 14, 2010 7:17 am 
Offline

Joined: Wed Nov 04, 2009 1:35 pm
Posts: 16
Location: Cambridge, UK
Hello,

I built gitorious efikasb-10.08.00 and it is working fine, but i am getting LVDS messages from kernel.

Packages are available at http://emdebian.org/~zumbi/docs/efikamx/

If you install the packages, you might either test flash-kernel from http://xxxx/ or you might want to manually run:
Code:
cd /boot
cp uImage uImage.bak
cp uInitrd uInitrd.bak

sudo mkimage -A arm -O linux -T kernel -C none -a 0x90008000 -e 0x90008000 -n "Efika kernel" -d vmlinuz-2.6.31.14.3-efikasb uImage

sudo mkimage -A arm -O linux -T ramdisk -C gzip -a 0x0 -e 0x0 -n "Efika initrd" -d initrd.img-2.6.31.14.3-efikasb uInitrd
Here my dmesg output
Code:
[ 0.000000] Linux version 2.6.31.14.3-efikasb (root@efikamx) (gcc version 4.4.5 (Ubuntu/Linaro 4.4.4-14ubuntu5) ) #2 Sun Nov 14 12:13:54 GMT 2010
[ 0.000000] CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: Genesi Efika MX (Smartbook)
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 106496
[ 0.000000] free_area_init_node: node 0, pgdat 804c134c, node_mem_map 80513000
[ 0.000000] DMA zone: 192 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 24384 pages, LIFO batch:3
[ 0.000000] Normal zone: 640 pages used for memmap
[ 0.000000] Normal zone: 81280 pages, LIFO batch:15
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 105664
[ 0.000000] Kernel command line: noinitrd console=ttymxc0,115200 console=tty1 root=/dev/sda2 ro
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 416MB = 416MB total
[ 0.000000] Memory: 416896KB available (4376K code, 531K data, 136K init, 0K highmem)
[ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:368
[ 0.000000] MXC IRQ initialized
[ 0.000000] MXC_Early serial console at MMIO 0x73fbc000 (options '115200')
[ 0.000000] console [ttymxc0] enabled
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console handover: boot [ttymxc0] -> real [tty1]
[ 0.000000] Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696)
[ 0.000000] Mount-cache hash table entries: 512
[ 0.000000] CPU: Testing write buffer coherency: ok
[ 0.000000] tmpfs: No value for mount option 'mode'
[ 0.000000] devtmpfs: initialized
[ 0.000000] regulator: core version 0.5
[ 0.000000] NET: Registered protocol family 16
[ 0.000000] i.MX IRAM pool: 128 KB@0x9a840000
[ 0.000000] IRAM READY
[ 0.000000] CPU is i.MX51 Revision 3.0
[ 0.000000] MXC GPIO hardware
[ 0.000000] [VV] mx51_efikasb_init_mc13892.
[ 0.000000] Using SDMA I.API
[ 0.000000] MXC DMA API initialized
[ 0.000000] bio: create slab <bio-0> at 0
[ 0.000000] SCSI subsystem initialized
[ 0.000000] libata version 3.00 loaded.
[ 0.000000] CSPI: mxc_spi-0 probed
[ 0.000000] usbcore: registered new interface driver usbfs
[ 0.000000] usbcore: registered new interface driver hub
[ 0.000000] usbcore: registered new device driver usb
[ 0.000000] IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
[ 0.000000] mc13892 Rev 2.0 FinVer 2 detected
[ 0.000000] Initializing regulators for Efika MX Smartbook
[ 0.000000] regulator: SW1: 600 <--> 1375 mV
[ 0.000000] regulator: SW2: 900 <--> 1850 mV
[ 0.000000] regulator: SW3: 1100 <--> 1850 mV
[ 0.000000] regulator: SW4: 1100 <--> 1850 mV
[ 0.000000] regulator: SWBST: 0 mV
[ 0.000000] regulator: VIOHI: 0 mV
[ 0.000000] regulator: VPLL: 1050 <--> 1800 mV
[ 0.000000] regulator: VDIG: 1650 mV
[ 0.000000] regulator: VSD: 1800 <--> 3150 mV
[ 0.000000] regulator: VUSB2: 2400 <--> 2775 mV
[ 0.000000] regulator: VVIDEO: 2775 mV
[ 0.000000] regulator: VAUDIO: 2300 <--> 3000 mV
[ 0.000000] regulator: VCAM: 2500 <--> 3000 mV fast normal
[ 0.000000] regulator: VGEN1: 1200 mV
[ 0.000000] regulator: VGEN2: 1200 <--> 3150 mV
[ 0.000000] regulator: VGEN3: 1800 <--> 2900 mV
[ 0.000000] regulator: VUSB: 0 mV
[ 0.000000] regulator: GPO1: 0 mV
[ 0.000000] regulator: GPO2: 0 mV
[ 0.000000] regulator: GPO3: 0 mV
[ 0.000000] regulator: GPO4: 0 mV
[ 0.000000] Device spi1.0 probed
[ 0.000000] NET: Registered protocol family 2
[ 0.000000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.870142] Switched to high resolution mode on CPU 0
[ 0.870767] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.871097] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.871264] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.871284] TCP reno registered
[ 0.871443] NET: Registered protocol family 1
[ 0.872169] LPMode driver module loaded
[ 0.872195] Static Power Management for Freescale i.MX51
[ 0.872442] PM driver module loaded
[ 0.872653] sdram autogating driver module loaded
[ 0.872924] Bus freq driver module loaded
[ 0.872972] mxc_dvfs_core_probe
[ 0.873198] DVFS driver module loaded
[ 0.873223] i.MXC CPU frequency driver
[ 0.873669] DVFS PER driver module loaded
[ 0.875069] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.875124] msgmni has been set to 814
[ 0.877850] alg: No test for stdrng (krng)
[ 0.878142] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.878177] io scheduler noop registered (default)
[ 0.878207] io scheduler cfq registered
[ 0.879544] mode_option=1024x600M-16@60
[ 0.879577] fbcvt: Aspect ratio not CVT standard
[ 0.879605] fbcvt: 1024x600@60: CVT Name - Not a CVT standard - 0.614 Mega Pixel Image
[ 0.879612]
[ 0.880629] mxc_ipu mxc_ipu: Channel already disabled 9
[ 0.880640] mxc_ipu mxc_ipu: Channel already uninitialized 9
[ 0.900178] IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
[ 0.905968] Console: switching to colour frame buffer device 128x37
[ 0.927056] EDID Dump:
[ 0.927130] 00ffffffffffff0006afd220000000000112010380160d780a2b699757559629
[ 0.927476] 214f5400000001010101010101010101010101010101b0130040415819201888
[ 0.927824] 3100df7d000000180000000f0000000000000000000000000020000000fe0041
[ 0.930757] 554f0a202020202020202020000000fe004231303141573032205630200a00c7
[ 0.933593] resolution: r(1024, 600), v(1024, 600) o(0, 0)
[ 0.936213] bpp=0, hw(0, 0), pclk=19841
[ 0.938780] margin(160, 24, 21, 3)
[ 0.941308] hv(136, 1), sync=0, vmode=0
[ 0.943799] mtl017: Probe LCD Panel: AUO B101AW02 V0
[ 1.080152] DMFC high resolution has set, will not change
[ 1.140373] mtl017 1-003a: Initializing MTL017 LVDS Controller
[ 1.349369] Serial: MXC Internal UART driver
[ 1.352314] mxcintuart.0: ttymxc0 at MMIO 0x73fbc000 (irq = 31) is a Freescale i.MX
[ 1.354985] console [ttymxc0] enabled
[ 2.131641] mxcintuart.1: ttymxc1 at MMIO 0x73fc0000 (irq = 32) is a Freescale i.MX
[ 2.143168] mxcintuart.2: ttymxc2 at MMIO 0x7000c000 (irq = 33) is a Freescale i.MX
[ 2.158233] loop: module loaded
[ 2.165317] pata_fsl pata_fsl: rchan=29 wchan=28
[ 2.172970] scsi0 : pata_fsl
[ 2.178972] ata1: PATA max UDMA/44 irq 70
[ 2.187580] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.300135] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[ 2.310195] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[ 2.350142] fsl-ehci fsl-ehci.0: irq 18, io base 0x73f80000
[ 2.361235] ata1.00: CFA: Flash Module, Ver2.M11, max UDMA/100
[ 2.369843] ata1.00: 30146256 sectors, multi 1: LBA
[ 2.377958] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[ 2.387114] usb usb1: configuration #1 chosen from 1 choice
[ 2.396283] hub 1-0:1.0: USB hub found
[ 2.402922] hub 1-0:1.0: 1 port detected
[ 2.414450] ata1.00: configured for UDMA/44
[ 2.421745] scsi 0:0:0:0: Direct-Access ATA Flash Module Ver2 PQ: 0 ANSI: 5
[ 2.433558] sd 0:0:0:0: [sda] 30146256 512-byte logical blocks: (15.4 GB/14.3 GiB)
[ 2.444193] sd 0:0:0:0: [sda] Write Protect is off
[ 2.451784] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.451885] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2.464444] sda:
[ 2.467386] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.479192] sda1 sda2
[ 2.485953] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.620135] fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
[ 2.630316] fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
[ 2.670143] fsl-ehci fsl-ehci.1: irq 14, io base 0x73f80200
[ 2.690131] fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
[ 2.699183] usb usb2: configuration #1 chosen from 1 choice
[ 2.707885] hub 2-0:1.0: USB hub found
[ 2.714398] hub 2-0:1.0: 1 port detected
[ 2.940127] usb 2-1: new high speed USB device using fsl-ehci and address 2
[ 2.949990] fsl-ehci fsl-ehci.2: Freescale On-Chip EHCI Host Controller
[ 2.960244] fsl-ehci fsl-ehci.2: new USB bus registered, assigned bus number 3
[ 3.000139] fsl-ehci fsl-ehci.2: irq 16, io base 0x73f80400
[ 3.100117] fsl-ehci fsl-ehci.2: USB 2.0 started, EHCI 1.00
[ 3.109144] usb usb3: configuration #1 chosen from 1 choice
[ 3.118044] hub 3-0:1.0: USB hub found
[ 3.124721] hub 3-0:1.0: 1 port detected
[ 3.132441] usb 2-1: configuration #1 chosen from 1 choice
[ 3.141397] usbcore: registered new interface driver libusual
[ 3.150551] hub 2-1:1.0: USB hub found
[ 3.157305] hub 2-1:1.0: 4 ports detected
[ 3.164756] mice: PS/2 mouse device common for all mice
[ 3.173119] MXC keypad loaded
[ 3.179549] mc13892 rtc probe start
[ 3.190791] pmic_rtc pmic_rtc.1: rtc core: registered pmic_rtc as rtc0
[ 3.200132] mc13892 rtc probe succeed
[ 3.206600] i2c /dev entries driver
[ 3.213502] Linux video capture interface: v2.00
[ 3.221774] MXC Video Output MXC Video Output.0: Registered device video0
[ 3.350125] usb 3-1: new high speed USB device using fsl-ehci and address 2
[ 3.511266] usb 3-1: configuration #1 chosen from 1 choice
[ 3.520043] hub 3-1:1.0: USB hub found
[ 3.526669] hub 3-1:1.0: 3 ports detected
[ 3.610366] usb 2-1.1: new low speed USB device using fsl-ehci and address 3
[ 3.741330] usb 2-1.1: configuration #1 chosen from 1 choice
[ 3.774828] Probe Efika MX Smartbook Battery: AS01BAB34B K2---28 Inserted: 99%, AC Inserted
[ 3.786167] MXC WatchDog Driver 2.0
[ 3.792517] clk: Unable to get requested clock: wdog_clk
[ 3.801128] MXC Watchdog # 0 Timer: initial timeout 60 sec
[ 3.809486] cpuidle: using governor ladder
[ 3.816342] cpuidle: using governor menu
[ 3.823549] PMIC Character device: successfully loaded
[ 3.831926] usb 2-1.2: new high speed USB device using fsl-ehci and address 4
[ 3.842482] VPU initialized
[ 3.848627] mxsdhci: MXC Secure Digital Host Controller Interface driver
[ 3.858321] mxsdhci: MXC SDHCI Controller Driver.
[ 3.866494] mmc0: SDHCI detect irq 187 irq 1 INTERNAL DMA
[ 3.874805] mxsdhci: MXC SDHCI Controller Driver.
[ 3.882739] mmc1: SDHCI detect irq 136 irq 2 INTERNAL DMA
[ 3.891306] Registered led device: msg-alarm-led
[ 3.898693] Registered Efika MX Smartbook Message Alarm LED
[ 3.928356] input: USB Keyboard as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.1/2-1.1:1.0/input/input0
[ 3.965179] generic-usb 0003:04D9:FF09.0001: input: USB HID v1.10 Keyboard [USB Keyboard] on usb-fsl-ehci.1-1.1/input0
[ 3.996899] input: USB Keyboard as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.1/2-1.1:1.1/input/input1
[ 4.034376] generic-usb 0003:04D9:FF09.0002: input: USB HID v1.10 Mouse [USB Keyboard] on usb-fsl-ehci.1-1.1/input1
[ 4.048558] usbcore: registered new interface driver usbhid
[ 4.057541] usbhid: v2.6:USB HID core driver
[ 4.066022] usb 2-1.2: configuration #1 chosen from 1 choice
[ 4.075306] Advanced Linux Sound Architecture Driver Version 1.0.20.
[ 4.160861] sgtl5000-i2c 1-000a: SGTL5000 revision 17
[ 4.227903] mmc1: new high speed SD card at address fb8d
[ 4.236696] usb 3-1.1: new full speed USB device using fsl-ehci and address 3
[ 4.247459] mmcblk0: mmc1:fb8d SD02G 1.83 GiB
[ 4.255507] mmcblk0: p1 p2
[ 4.266349] No device for DAI imx-ssi-1-0
[ 4.274645] No device for DAI imx-ssi-1-1
[ 4.281867] No device for DAI imx-ssi-2-0
[ 4.288984] No device for DAI imx-ssi-2-1
[ 4.296920] DMA Sound Buffers Allocated:UseIram=1 buf->addr=1fff6000 buf->area=9a856000 size=24576
[ 4.309379] DMA Sound Buffers Allocated:UseIram=1 buf->addr=a8308000 buf->area=f9e80000 size=24576
[ 4.321621] asoc: SGTL5000 <-> imx-ssi-2-0 mapping ok
[ 4.350354] usb 3-1.1: device descriptor read/64, error -32
[ 4.382853] ALSA device list:
[ 4.388964] #0: imx-3stack (SGTL5000)
[ 4.396567] TCP cubic registered
[ 4.402817] NET: Registered protocol family 17
[ 4.410282] ThumbEE CPU extension supported.
[ 4.418442] input: Genesi Efika MX Smartbook Extra Buttons as /devices/virtual/input/input2
[ 4.431405] input: Efika MX Smartbook Lid Switch as /devices/virtual/input/input3
[ 4.442652] Lid Switch Open
[ 4.448877] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
[ 4.461705] regulator_init_complete: disabling GPO4
[ 4.470966] regulator_init_complete: disabling GPO3
[ 4.490229] regulator_init_complete: disabling GPO2
[ 4.510161] regulator_init_complete: disabling GPO1
[ 4.547766] regulator_init_complete: disabling VGEN1
[ 4.555825] usb 3-1.1: device descriptor read/64, error -32
[ 4.564354] regulator_init_complete: disabling VCAM
[ 4.670900] regulator_init_complete: disabling VAUDIO
[ 4.679050] regulator_init_complete: disabling VSD
[ 4.690302] regulator_init_complete: disabling SWBST
[ 4.770978] pmic_rtc pmic_rtc.1: setting system clock to 2010-11-14 12:38:04 UTC (1289738284)
[ 4.782909] usb 3-1.1: new full speed USB device using fsl-ehci and address 4
[ 4.792928] EXT3-fs: sda2: couldn't mount because of unsupported optional features (240).
[ 4.804678] EXT2-fs: sda2: couldn't mount because of unsupported optional features (244).
[ 4.818344] EXT4-fs (sda2): INFO: recovery required on readonly filesystem
[ 4.827839] EXT4-fs (sda2): write access will be enabled during recovery
[ 4.838027] EXT4-fs (sda2): barriers enabled
[ 4.891677] usb 3-1.1: device descriptor read/64, error -32
[ 5.090372] usb 3-1.1: device descriptor read/64, error -32
[ 5.280379] usb 3-1.1: new full speed USB device using fsl-ehci and address 5
[ 5.710145] usb 3-1.1: device not accepting address 5, error -32
[ 5.800367] usb 3-1.1: new full speed USB device using fsl-ehci and address 6
[ 6.230144] usb 3-1.1: device not accepting address 6, error -32
[ 6.240997] hub 3-1:1.0: unable to enumerate USB device on port 1
[ 6.330369] usb 3-1.2: new high speed USB device using fsl-ehci and address 7
[ 6.473522] usb 3-1.2: configuration #1 chosen from 1 choice
[ 16.092558] kjournald2 starting: pid 1066, dev sda2:8, commit interval 5 seconds
[ 16.102882] EXT4-fs (sda2): delayed allocation enabled
[ 16.110706] EXT4-fs: file extents enabled
[ 16.120003] EXT4-fs: mballoc enabled
[ 16.126094] EXT4-fs (sda2): recovery complete
[ 16.391770] EXT4-fs (sda2): mounted filesystem with ordered data mode
[ 16.400974] VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
[ 16.440934] devtmpfs: mounted
[ 16.446591] Freeing init memory: 136K
[ 18.120664] udev[1103]: starting version 163
[ 19.295660] rt2870sta: module is from the staging directory, the quality is unknown, you have been warned.
[ 19.550747] rtusb init --->
[ 19.562402] uvcvideo: Found UVC 1.00 device Pegatron (04f2:b1b0)
[ 19.601083] input: Pegatron as /devices/platform/fsl-ehci.2/usb3/3-1/3-1.2/3-1.2:1.0/input/input4
[ 19.602085] usbcore: registered new interface driver uvcvideo
[ 19.602105] USB Video Class driver (v0.1.0)
[ 19.733396] usbcore: registered new interface driver rt2870
[ 21.888156] EXT4-fs (sda2): internal journal on sda2:8
[ 22.824286] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 23.754144] Adding 131064k swap on /swapfile. Priority:-1 extents:5 across:303100k SS
[ 26.311618] usb 2-1.2: firmware: requesting rt3070.bin
[ 27.489649] 0x1300 = 00073200
[ 27.970332] DMFC high resolution has set, will not change
[ 28.737896] 0x1300 = 00073200
[ 29.864883] mxc_ipu mxc_ipu: Channel already disabled 9
[ 29.864897] mxc_ipu mxc_ipu: Channel already uninitialized 9
[ 29.890445] DMFC high resolution has set, will not change
[ 29.950218] mtl017 1-003a: Initializing MTL017 LVDS Controller
[ 300.297219] 0x1300 = 000a4200
[ 110.583836] 0x1300 = 000a4200
[ 160.073067] mxc_ipu mxc_ipu: Channel already disabled 9
[ 160.073122] mxc_ipu mxc_ipu: Channel already uninitialized 9
[ 160.089787] DMFC high resolution has set, will not change
[ 160.149333] mtl017 1-003a: Initializing MTL017 LVDS Controller
[ 160.169970] MTL017 LVDS Controller Initialize Fail!
[ 160.189754] MTL017 LVDS Controller Initialize Fail!
[ 160.209388] MTL017 LVDS Controller Initialize Fail!
[ 160.229387] MTL017 LVDS Controller Initialize Fail!
[ 160.249413] MTL017 LVDS Controller Initialize Fail!
[ 160.269867] MTL017 LVDS Controller Initialize Fail!
[ 192.417895] 0x1300 = 000a4200
[ 267.245704] mxc_ipu mxc_ipu: Channel already disabled 9
[ 267.245760] mxc_ipu mxc_ipu: Channel already uninitialized 9
[ 267.259255] DMFC high resolution has set, will not change
[ 267.319074] mtl017 1-003a: Initializing MTL017 LVDS Controller
[ 267.339126] MTL017 LVDS Controller Initialize Fail!
[ 267.359125] MTL017 LVDS Controller Initialize Fail!
[ 267.379131] MTL017 LVDS Controller Initialize Fail!
[ 267.399696] MTL017 LVDS Controller Initialize Fail!
[ 267.419135] MTL017 LVDS Controller Initialize Fail!
[ 267.440810] MTL017 LVDS Controller Initialize Fail!
[ 332.106741] mxc_ipu mxc_ipu: Channel already disabled 9
[ 332.106797] mxc_ipu mxc_ipu: Channel already uninitialized 9
[ 332.118343] DMFC high resolution has set, will not change
[ 332.178134] mtl017 1-003a: Initializing MTL017 LVDS Controller
[ 332.198198] MTL017 LVDS Controller Initialize Fail!
[ 332.218206] MTL017 LVDS Controller Initialize Fail!
[ 332.238172] MTL017 LVDS Controller Initialize Fail!
[ 332.258201] MTL017 LVDS Controller Initialize Fail!
[ 332.278185] MTL017 LVDS Controller Initialize Fail!
[ 332.298200] MTL017 LVDS Controller Initialize Fail!

_________________
-- Hector Oron <zumbi>


Last edited by zumbi on Sun Nov 14, 2010 11:54 am, edited 1 time in total.

Top
   
PostPosted: Sun Nov 14, 2010 11:23 am 
Offline
Site Admin

Joined: Fri Sep 24, 2004 1:39 am
Posts: 1589
Location: Austin, TX
Quote:
Hello,

I built gitorious efikasb-10.08.00 and it is working fine, but i am getting LVDS messages from kernel.

Packages are available at http://emdebian.org/~zumbi/docs/efikamx/

If you install the packages, you might either test flash-kernel from http://packages.efikamx.info/
Kernel will be up in a couple hours too. However, that repo is a little unstable right now (we're still configuring it, I just posted it to IRC so people could get a grip on what we're doing :)

Ignore LVDS Initialize Fail!, it is just because it was already initialized (otherwise it does an EDID check again). It doesn't fail so much as skip initialization. We're rewriting that driver to be less braindead :)

_________________
Matt Sealey


Top
   
 Post subject:
PostPosted: Sun Nov 14, 2010 2:32 pm 
Offline

Joined: Thu Jul 28, 2005 12:41 am
Posts: 1066
What is the correct way to install it?
Code:
echo deb http://packages.efikamx.info/ maverick main >> /etc/apt.sources.list
apt-get update
apt-get dist-upgrade
Is this OK? Or I need different settings, more commands...

_________________
CzP
http://czanik.blogs.balabit.com/


Top
   
 Post subject:
PostPosted: Mon Nov 15, 2010 1:16 am 
Offline
Site Admin

Joined: Fri Sep 24, 2004 1:39 am
Posts: 1589
Location: Austin, TX
Quote:
What is the correct way to install it?
Code:
echo deb http://packages.efikamx.info/ maverick main >> /etc/apt.sources.list
apt-get update
apt-get dist-upgrade
Is this OK? Or I need different settings, more commands...
I wouldn't do a dist-upgrade :)

apt-get install linux-image-2.6.31.14.7-efika{mx,sb}-10.08.00

will do, probably.

_________________
Matt Sealey


Top
   
PostPosted: Tue Nov 16, 2010 2:58 am 
Offline

Joined: Wed Jul 01, 2009 4:35 pm
Posts: 94
Location: Italy
This kernel is for all?
And fix what?
fix suspend/resume usb/keyboard/mouse problem?
Any news about adobe flash for maverick?

Thanks
Quote:

I wouldn't do a dist-upgrade :)

apt-get install linux-image-2.6.31.14.7-efika{mx,sb}-10.08.00

will do, probably.

_________________
http://deliriotecnologico.blogspot.com


Top
   
PostPosted: Tue Nov 16, 2010 11:14 am 
Offline
Site Admin

Joined: Fri Sep 24, 2004 1:39 am
Posts: 1589
Location: Austin, TX
Quote:
This kernel is for all?
It'll work.
Quote:
And fix what?
On Smartbook: battery gauge issues and the pixel offset panel bug. There are also some stability fixes and GPU updates.
Quote:
fix suspend/resume usb/keyboard/mouse problem?
No. Just don't suspend for now. If you close the lid and set it to blank screen instead of Suspend, you will get around 7-8 hours of battery life anyway.
Quote:
Any news about adobe flash for maverick?
It will probably NOT be released in the immediate future as there are licensing and certification issues to tend to.

_________________
Matt Sealey


Top
   
 Post subject: apt source dir
PostPosted: Tue Nov 16, 2010 5:27 pm 
Offline

Joined: Wed Jul 01, 2009 4:35 pm
Posts: 94
Location: Italy
the right place to append the repository address in my Smartbook with Maverick is:
Code:
/etc/apt/sources.list
so the command ,must be:
Code:
echo deb http://packages.efikamx.info/ maverick main >> /etc/apt/sources.list
In my case after that I have write:
Code:
apt-get install linux-image-2.6.31.14.7-efikasb
Quote:
Quote:
What is the correct way to install it?
Code:
echo deb http://packages.efikamx.info/ maverick main >> /etc/apt.sources.list
apt-get update
apt-get dist-upgrade
Is this OK? Or I need different settings, more commands...
I wouldn't do a dist-upgrade :)

apt-get install linux-image-2.6.31.14.7-efika{mx,sb}-10.08.00

will do, probably.

_________________
http://deliriotecnologico.blogspot.com


Top
   
PostPosted: Tue Nov 16, 2010 5:41 pm 
Offline

Joined: Wed Jul 01, 2009 4:35 pm
Posts: 94
Location: Italy
I think si better to have a signature for
http://packages.efikamx.info/ repository

Becouse without signature the proposed update will be not possible to perform .

It make the update only with
Code:
sudo apt-get upgrade

_________________
http://deliriotecnologico.blogspot.com


Top
   
PostPosted: Tue Nov 16, 2010 7:12 pm 
Offline

Joined: Wed Jul 01, 2009 4:35 pm
Posts: 94
Location: Italy
After installing kernel 2.6.31.14.7 I still see the not used 5 pixel on the button of the lcd, the battery calculation time is wrong as usual.

I have make the upgrade and installed specifically imx-lib,libz160, but I couldn't see any improvement in 2D in the game like SMC, it is still unusable.
Quote:
Quote:
This kernel is for all?
It'll work.
Quote:
And fix what?
On Smartbook: battery gauge issues and the pixel offset panel bug. There are also some stability fixes and GPU updates.
Quote:
fix suspend/resume usb/keyboard/mouse problem?

_________________
http://deliriotecnologico.blogspot.com


Top
   
 Post subject:
PostPosted: Wed Nov 17, 2010 2:19 am 
Offline

Joined: Thu Jul 28, 2005 12:41 am
Posts: 1066
Are you sure, that your SB runs on the latest kernel now? As for me both problems are fixed after the update.
Code:
czanik@czp-laptop:~$ uname -a
Linux czp-laptop 2.6.31.14.7-efikasb #12 Sat Nov 13 10:53:10 CST 2010 armv7l GNx

_________________
CzP
http://czanik.blogs.balabit.com/


Top
   
 Post subject: to check
PostPosted: Wed Nov 17, 2010 9:38 am 
Offline

Joined: Wed Jul 01, 2009 4:35 pm
Posts: 94
Location: Italy
In fact was the first things that I have reflect to, so last night I have checked the directory
Code:
/boot
and I have found 2.6.31.14.7-efikasb, and I have made
Code:
uname -a
, but if I don't remember well the only strange things was that with uname I don't saw .7 only 2.6.31.14, but was late... so this night I will check again, I will be probably tired like last night... :D

Another things that I must check is the suffix -10.08.00 of the kernel, becouse when I have installed the kernel I have not specify the suffix.

Thanks

Roberto
Quote:
Are you sure, that your SB runs on the latest kernel now? As for me both problems are fixed after the update.
Code:
czanik@czp-laptop:~$ uname -a
Linux czp-laptop 2.6.31.14.7-efikasb #12 Sat Nov 13 10:53:10 CST 2010 armv7l GNx
Quote:

_________________
http://deliriotecnologico.blogspot.com


Top
   
PostPosted: Wed Nov 17, 2010 7:25 pm 
Offline

Joined: Wed Jul 01, 2009 4:35 pm
Posts: 94
Location: Italy
after add the repository, install the new kernel, is needed to make uImage and uInitrd, as suggested from zumbi:
Code:
cd /boot
cp uImage uImage.bak
cp uInitrd uInitrd.bak

sudo mkimage -A arm -O linux -T kernel -C none -a 0x90008000 -e 0x90008000 -n "Efika kernel" -d vmlinuz-2.6.31.14.7-efikasb uImage

sudo mkimage -A arm -O linux -T ramdisk -C gzip -a 0x0 -e 0x0 -n "Efika initrd" -d initrd.img-2.6.31.14.7-efikasb uInitrd
After that i have reboot SB and doing
Code:
roby@efikamx:~$ uname -a
Linux efikamx 2.6.31.14.7-efikasb #12 Sat Nov 13 10:53:10 CST 2010 armv7l GNU/Linux
Appear the right kernel and in fact the 5 pixel at bottom now are fixed! good!

Other improvement now when I shut down I can see the message power down, still without switch off the SB, anyway an improvment.

_________________
http://deliriotecnologico.blogspot.com


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 12 posts ] 

All times are UTC-06:00


Who is online

Users browsing this forum: No registered users and 9 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
cron
PowerDeveloper.org: Copyright © 2004-2012, Genesi USA, Inc. The Power Architecture and Power.org wordmarks and the Power and Power.org logos and related marks are trademarks and service marks licensed by Power.org.
All other names and trademarks used are property of their respective owners. Privacy Policy
Powered by phpBB® Forum Software © phpBB Group