Power Developer https://www.powerdeveloper.org/forums/ |
|
Debian armhf boot log https://www.powerdeveloper.org/forums/viewtopic.php?f=7&t=1903 |
Page 1 of 1 |
Author: | zumbi [ Tue Dec 21, 2010 10:12 am ] |
Post subject: | Debian armhf boot log |
Hello, Just in case it is useful for someone. There is a boot log. The kernel image used is the one already compiled at powerdeveloper site. Code:
U-Boot 2009.01-1.2.19-lange51 (May 06 2010 - 11:52:45)
CPU: Freescale i.MX51 family 3.0V at 800 MHz mx51 pll1: 800MHz mx51 pll2: 665MHz mx51 pll3: 216MHz ipg clock : 66500000Hz ipg per clock : 665000000Hz uart clock : 66500000Hz cspi clock : 54000000Hz Board: MX51 LANGE51 3.0 [POR] DRAM: 512 MB JEDEC ID: 0xbf:0x25:0x4a Reading SPI NOR flash 0x40000 [0x10000 bytes] -> ram 0x975f06e8 .SUCCESS *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial board id: 1.0.1, rev1.3 Boot Source: SPI NOR FLASH BOOT SD card. Vendor: Man 28 OEM BE "LEXAR" Date 10/2010 Product: 95977 Revision: 1.0 reading uImage reading system.conf ** Unable to read "system.conf" from mmc 0:1 ** Boot Cmd: run sd_boot Hit any key to stop autoboot: 1 0 ## Error: "base_cmd99" not defined SD card. Vendor: Man 28 OEM BE "LEXAR" Date 10/2010 Product: 95977 Revision: 1.0 reading uImage ## Booting kernel from Legacy Image at 90007fc0 ... Image Name: Linux-2.6.31.14-efikamx Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2658376 Bytes = 2.5 MB Load Address: 90008000 Entry Point: 90008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux................................................................................................................................................................. done, booting the kernel. [ 0.000000] Linux version 2.6.31.14-efikamx (neko@excel) (gcc version 4.4.1 (Sourcery G++ Lite 2010q1-202) ) #1 PREEMPT Tue Sep 14 22:23:30 CDT 2010 [ 0.000000] CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c53c7f [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache [ 0.000000] Machine: Genesi Efika MX (Smarttop) [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 105664 [ 0.000000] Kernel command line: noinitrd console=ttymxc0,115200 console=tty1 root=/dev/mmcblk0p2 rw [ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 416MB = 416MB total [ 0.000000] Memory: 416700KB available (4556K code, 528K data, 140K init, 0K highmem) [ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:368 [ 0.000000] MXC IRQ initialized [ 0.000000] MXC_Early serial console at MMIO 0x73fbc000 (options '115200') [ 0.000000] console [ttymxc0] enabled [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] console handover: boot [ttymxc0] -> real [tty1] [ 0.000000] Linux version 2.6.31.14-efikamx (neko@excel) (gcc version 4.4.1 (Sourcery G++ Lite 2010q1-202) ) #1 PREEMPT Tue Sep 14 22:23:30 CDT 2010 [ 0.000000] CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c53c7f [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache [ 0.000000] Machine: Genesi Efika MX (Smarttop) [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 105664 [ 0.000000] Kernel command line: noinitrd console=ttymxc0,115200 console=tty1 root=/dev/mmcblk0p2 rw [ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 416MB = 416MB total [ 0.000000] Memory: 416700KB available (4556K code, 528K data, 140K init, 0K highmem) [ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:368 [ 0.000000] MXC IRQ initialized [ 0.000000] MXC_Early serial console at MMIO 0x73fbc000 (options '115200') [ 0.000000] console [ttymxc0] enabled [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] console handover: boot [ttymxc0] -> real [tty1] [ 0.000000] Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696) [ 0.000000] Mount-cache hash table entries: 512 [ 0.000000] CPU: Testing write buffer coherency: ok [ 0.000000] tmpfs: No value for mount option 'mode' [ 0.000000] devtmpfs: initialized [ 0.000000] regulator: core version 0.5 [ 0.000000] NET: Registered protocol family 16 [ 0.000000] i.MX IRAM pool: 128 KB@0x9a840000 [ 0.000000] IRAM READY [ 0.000000] CPU is i.MX51 Revision 3.0 [ 0.000000] MXC GPIO hardware [ 0.000000] Efika MX: IOMUX for Board ID (3 pins) [ 0.000000] Efika MX: IOMUX for General GPIO Stuff (7 pins) [ 0.000000] Efika MX: IOMUX for SPI (6 pins) [ 0.000000] Efika MX: IOMUX for PMIC (1 pins) [ 0.000000] Efika MX: IOMUX for I2C (4 pins) [ 0.000000] Efika MX: IOMUX for USB (29 pins) [ 0.000000] Efika MX: IOMUX for ATA (29 pins) [ 0.000000] Efika MX: Initializing SD card IOMUX (external, mmc0) [ 0.000000] Efika MX: IOMUX for WDOG (1.2) (1 pins) [ 0.000000] Efika MX: IOMUX for LED (3 pins) [ 0.000000] Efika MX: IOMUX for Power Key (1 pins) [ 0.000000] Efika MX: AIPS1_BASE_ADDR = 0x73f00000 [ 0.000000] Efika MX: AIPS1_BASE_ADDR_VIRT = 0xf7e00000, io_pg_offst = 0x3df8 [ 0.000000] Efika MX: PHYS_OFFSET = 0x90000000 [ 0.000000] Efika MX Revision 1.3 [ 0.000000] Using SDMA I.API [ 0.000000] MXC DMA API initialized [ 0.000000] bio: create slab <bio-0> at 0 [ 0.000000] SCSI subsystem initialized [ 0.000000] CSPI: mxc_spi-0 probed [ 0.000000] usbcore: registered new interface driver usbfs [ 0.000000] usbcore: registered new interface driver hub [ 0.000000] usbcore: registered new device driver usb [ 0.000000] IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7) [ 0.000000] mc13892 Rev 2.0 FinVer 2 detected [ 0.000000] Initializing regulators for Efika MX [ 0.000000] regulator: SW1: 600 <--> 1375 mV [ 0.000000] regulator: SW2: 900 <--> 1850 mV [ 0.000000] regulator: SW3: 1100 <--> 1850 mV [ 0.000000] regulator: SW4: 1100 <--> 1850 mV [ 0.000000] regulator: SWBST: 0 mV [ 0.000000] regulator: VIOHI: 0 mV [ 0.000000] regulator: VPLL: 1050 <--> 1800 mV [ 0.000000] regulator: VDIG: 1650 mV [ 0.000000] regulator: VSD: 1800 <--> 3150 mV [ 0.000000] regulator: VUSB2: 2400 <--> 2775 mV [ 0.000000] regulator: VVIDEO: 2775 mV [ 0.000000] regulator: VAUDIO: 2300 <--> 3000 mV [ 0.000000] regulator: VCAM: 2500 <--> 3000 mV fast normal [ 0.000000] regulator: VGEN1: 1200 <--> 3150 mV [ 0.000000] regulator: VGEN2: 1200 <--> 3150 mV [ 0.000000] regulator: VGEN3: 1800 <--> 2900 mV [ 0.000000] regulator: VUSB: 0 mV [ 0.000000] regulator: GPO1: 0 mV [ 0.000000] regulator: GPO2: 0 mV [ 0.000000] regulator: GPO3: 0 mV [ 0.000000] regulator: GPO4: 0 mV [ 0.000000] Device spi1.0 probed [ 0.532826] NET: Registered protocol family 2 [ 0.533161] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.534030] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.534612] TCP bind hash table entries: 16384 (order: 4, 65536 bytes) [ 0.534908] TCP: Hash tables configured (established 16384 bind 16384) [ 0.534935] TCP reno registered [ 0.535123] NET: Registered protocol family 1 [ 0.535938] LPMode driver module loaded [ 0.535971] Static Power Management for Freescale i.MX51 [ 0.536266] PM driver module loaded [ 0.536525] sdram autogating driver module loaded [ 0.536835] Bus freq driver module loaded [ 0.536891] mxc_dvfs_core_probe [ 0.537155] DVFS driver module loaded [ 0.537187] i.MXC CPU frequency driver [ 0.537709] DVFS PER driver module loaded [ 0.539812] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.539884] msgmni has been set to 814 [ 0.543548] alg: No test for stdrng (krng) [ 0.543902] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.543947] io scheduler noop registered (default) [ 0.543983] io scheduler cfq registered [ 0.544486] *** sii9022_probe [ 0.546777] SII9022 sink not found ! id=00 [ 0.568373] mxcfb_read_edid2 [ 0.568748] read_edid error! [ 0.568946] *** mxc_init_fb vmode= video-mode=1 clock_auto=1 [ 0.568971] registering framebuffer for HDMI [ 0.570042] mode_option=800x600-16@60 [ 0.570820] mxc_ipu mxc_ipu: Channel already disabled 9 [ 0.570831] mxc_ipu mxc_ipu: Channel already uninitialized 9 [ 0.570848] mxcfb_di_clock_adjust pixelclk=25000 rate=80000000 [ 0.570898] orig: parent=pll3 clk=216000000 this=ipu_di0_clk di_clk=27000000 [ 0.571023] adjust: parent=pll3 clk=80000000 this=ipu_di0_clk di_clk=40000000 ret=0 ret=0 [ 0.571134] skip sii9022_reinit! [ 0.571164] mxc_ipu mxc_ipu: WARNING: adapt panel end blank lines [ 0.738406] pclk 25000 same to previous one, skipping! [ 0.738416] skip sii9022_reinit! [ 0.738434] mxc_ipu mxc_ipu: WARNING: adapt panel end blank lines [ 0.762860] Console: switching to colour frame buffer device 100x37 [ 0.908394] pclk 25000 same to previous one, skipping! [ 0.908401] skip sii9022_reinit! [ 0.908418] mxc_ipu mxc_ipu: WARNING: adapt panel end blank lines [ 0.948396] registering framebuffer for VPU overlay [ 0.950976] mxc_sdc_fb mxc_sdc_fb.2: Unable to allocate framebuffer memory [ 0.953252] mxc_sdc_fb: probe of mxc_sdc_fb.2 failed with error -12 [ 0.955486] *** sii9022 lcd_probe [ 0.957694] *** sii9022 lcd_init_fb [ 0.978373] mxcfb_read_edid2 [ 0.980932] read_edid error! [ 0.983296] mxcfb_update_default_var mode_opt=<NULL> vmode= [ 0.985546] mxcfb_di_clock_adjust pixelclk=13468 rate=148500000 [ 0.987815] orig: parent=pll3 clk=80000000 this=ipu_di0_clk di_clk=40000000 [ 0.990204] adjust: parent=pll3 clk=148500000 this=ipu_di0_clk di_clk=74250000 ret=0 ret=0 [ 0.992563] sii9022_reinit 1280x720 13468 [ 1.132398] sii9022 1-0039: geometry 1280 720 1280 720 0 [ 1.134686] sii9022 1-0039: timings 13468 220 110 20 5 40 5 [ 1.136951] sii9022 1-0039: accel 0 sync 23 vmode=0 [ 1.139230] sii9022 1-0039: pclk 7425 refresh 6024 total x 1650 y 750 [ 1.141528] sii9022 1-0039: vmap idx=6 vcode=4 [ 1.144203] hdmi audio mute [ 1.154613] hdmi audio unmute [ 1.298398] pclk 13468 same to previous one, skipping! [ 1.298409] sii9022_reinit 1280x720 13468 same to previous one, skipping [ 1.318404] IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7) [ 1.335385] sii9022 1-0039: turning on LCD [ 1.614784] Serial: MXC Internal UART driver [ 1.615121] mxcintuart.0: ttymxc0 at MMIO 0x73fbc000 (irq = 31) is a Freescale i.MX [ 1.615335] console [ttymxc0] enabled [ 2.769313] mxcintuart.1: ttymxc1 at MMIO 0x73fc0000 (irq = 32) is a Freescale i.MX [ 2.781877] mxcintuart.2: ttymxc2 at MMIO 0x7000c000 (irq = 33) is a Freescale i.MX [ 2.798260] loop: module loaded [ 2.806393] pata_fsl pata_fsl: rchan=29 wchan=28 [ 2.815058] scsi0 : pata_fsl [ 2.822054] ata1: PATA max UDMA/44 irq 70 [ 2.831957] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.948393] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller [ 2.959372] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 [ 2.998406] fsl-ehci fsl-ehci.0: irq 18, io base 0x73f80000 [ 3.011248] ata1.00: ATA-8: SanDisk pSSD-P2 8GB, SSD 5.20, max UDMA/133 [ 3.021532] ata1.00: 15649200 sectors, multi 0: LBA48 [ 3.030621] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00 [ 3.040720] usb usb1: configuration #1 chosen from 1 choice [ 3.050852] hub 1-0:1.0: USB hub found [ 3.058179] hub 1-0:1.0: 1 port detected [ 3.074563] ata1.00: configured for UDMA/44 [ 3.098712] scsi 0:0:0:0: Direct-Access ATA SanDisk pSSD-P2 SSD PQ: 0 ANSI: 5 [ 3.111464] sd 0:0:0:0: [sda] 15649200 512-byte logical blocks: (8.01 GB/7.46 GiB) [ 3.123020] sd 0:0:0:0: [sda] Write Protect is off [ 3.131565] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.144906] sda: [ 3.147987] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 3.161508] sda1 sda2 [ 3.169547] sd 0:0:0:0: [sda] Attached SCSI disk [ 3.278399] fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller [ 3.289395] usb 1-1: new high speed USB device using fsl-ehci and address 2 [ 3.300535] fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2 [ 3.338404] fsl-ehci fsl-ehci.1: irq 14, io base 0x73f80200 [ 3.448377] fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00 [ 3.458584] usb usb2: configuration #1 chosen from 1 choice [ 3.468551] hub 2-0:1.0: USB hub found [ 3.476183] hub 2-0:1.0: 1 port detected [ 3.484580] usbcore: registered new interface driver libusual [ 3.495489] mice: PS/2 mouse device common for all mice [ 3.505055] MXC keypad loaded [ 3.512618] mc13892 rtc probe start [ 3.520922] usb 1-1: configuration #1 chosen from 1 choice [ 3.531451] pmic_rtc pmic_rtc.1: rtc core: registered pmic_rtc as rtc0 [ 3.541964] mc13892 rtc probe succeed [ 3.550067] i2c /dev entries driver [ 3.558198] Linux video capture interface: v2.00 [ 3.568078] MXC Video Output MXC Video Output.0: Registered device video0 [ 3.578765] MXC WatchDog Driver 2.0 [ 3.586083] clk: Unable to get requested clock: wdog_clk [ 3.595763] MXC Watchdog # 0 Timer: initial timeout 60 sec [ 3.605464] cpuidle: using governor ladder [ 3.613345] cpuidle: using governor menu [ 3.621599] PMIC Character device: successfully loaded [ 3.631326] VPU initialized [ 3.638190] mxsdhci: MXC Secure Digital Host Controller Interface driver [ 3.648697] mxsdhci: MXC SDHCI Controller Driver. [ 3.657452] mmc0: SDHCI detect irq 128 irq 1 INTERNAL DMA [ 3.667073] Registered led device: efikamx:green [ 3.675460] Registered led device: efikamx:red [ 3.693820] Registered led device: efikamx:blue [ 3.706352] usbcore: registered new interface driver usbhid [ 3.715622] usbhid: v2.6:USB HID core driver [ 3.734753] Advanced Linux Sound Architecture Driver Version 1.0.20. [ 3.793505] sgtl5000-i2c 1-000a: SGTL5000 revision 17 [ 3.808411] usb 2-1: new high speed USB device using fsl-ehci and address 2 [ 3.866281] mmc0: new high speed SDHC card at address b368 [ 3.875810] mmcblk0: mmc0:b368 LEXAR 3.73 GiB [ 3.884201] mmcblk0: p1 p2 [ 3.900103] No device for DAI imx-ssi-1-0 [ 3.907526] No device for DAI imx-ssi-1-1 [ 3.914982] No device for DAI imx-ssi-2-0 [ 3.922336] No device for DAI imx-ssi-2-1 [ 3.930551] DMA Sound Buffers Allocated:UseIram=1 buf->addr=1fff6000 buf->area=9a856000 size=24576 [ 3.943192] DMA Sound Buffers Allocated:UseIram=1 buf->addr=a8318000 buf->area=f9e30000 size=24576 [ 3.955495] asoc: SGTL5000 <-> imx-ssi-2-0 mapping ok [ 3.989988] usb 2-1: configuration #1 chosen from 1 choice [ 3.999556] hub 2-1:1.0: USB hub found [ 4.006717] hub 2-1:1.0: 4 ports detected [ 4.026124] ALSA device list: [ 4.032626] #0: imx-3stack (SGTL5000) [ 4.040548] TCP cubic registered [ 4.047047] NET: Registered protocol family 17 [ 4.054779] ThumbEE CPU extension supported. [ 4.062331] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2 [ 4.075112] regulator_init_complete: incomplete constraints, leaving GPO4 on [ 4.085796] regulator_init_complete: incomplete constraints, leaving GPO3 on [ 4.096138] regulator_init_complete: incomplete constraints, leaving GPO2 on [ 4.106384] regulator_init_complete: incomplete constraints, leaving GPO1 on [ 4.116553] regulator_init_complete: incomplete constraints, leaving VGEN3 on [ 4.126646] regulator_init_complete: incomplete constraints, leaving VGEN2 on [ 4.136811] regulator_init_complete: incomplete constraints, leaving VGEN1 on [ 4.146886] regulator_init_complete: incomplete constraints, leaving VCAM on [ 4.156818] regulator_init_complete: incomplete constraints, leaving VAUDIO on [ 4.166893] regulator_init_complete: incomplete constraints, leaving VSD on [ 4.176537] regulator_init_complete: incomplete constraints, leaving SWBST on [ 4.186916] pmic_rtc pmic_rtc.1: setting system clock to 1970-01-01 06:41:57 UTC (24117) [ 4.199709] EXT3-fs: mmcblk0p2: couldn't mount because of unsupported optional features (240). [ 4.212054] EXT2-fs: mmcblk0p2: couldn't mount because of unsupported optional features (240). [ 4.244032] EXT4-fs (mmcblk0p2): barriers enabled [ 4.252663] kjournald2 starting: pid 1027, dev mmcblk0p2:8, commit interval 5 seconds [ 4.269148] EXT4-fs (mmcblk0p2): internal journal on mmcblk0p2:8 [ 4.278095] EXT4-fs (mmcblk0p2): delayed allocation enabled [ 4.286467] EXT4-fs: file extents enabled [ 4.294480] EXT4-fs: mballoc enabled [ 4.301026] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode [ 4.310967] VFS: Mounted root (ext4 filesystem) on device 179:2. [ 4.321338] devtmpfs: mounted [ 4.327640] Freeing init memory: 140K [ 4.408696] usb 2-1.1: new high speed USB device using fsl-ehci and address 3 [ 4.548136] usb 2-1.1: configuration #1 chosen from 1 choice Debian GNU/Linux squeeze/sid (none) ttymxc0 (none) login: root Password: Last login: Thu Jan 1 07:00:35 BST 1970 on ttymxc0 Linux (none) 2.6.31.14-efikamx #1 PREEMPT Tue Sep 14 22:23:30 CDT 2010 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@(none):~# dpkg --print-architecture armhf root@(none):~# dpkg-architecture sh: gcc: not found dpkg-architecture: warning: Couldn't determine gcc system type, falling back to default (native compilation) DEB_BUILD_ARCH=armhf DEB_BUILD_ARCH_OS=linux DEB_BUILD_ARCH_CPU=arm DEB_BUILD_ARCH_BITS=32 DEB_BUILD_ARCH_ENDIAN=little DEB_BUILD_GNU_CPU=arm DEB_BUILD_GNU_SYSTEM=hardfloat-linux-gnueabi DEB_BUILD_GNU_TYPE=arm-hardfloat-linux-gnueabi DEB_HOST_ARCH=armhf DEB_HOST_ARCH_OS=linux DEB_HOST_ARCH_CPU=arm DEB_HOST_ARCH_BITS=32 DEB_HOST_ARCH_ENDIAN=little DEB_HOST_GNU_CPU=arm DEB_HOST_GNU_SYSTEM=hardfloat-linux-gnueabi DEB_HOST_GNU_TYPE=arm-hardfloat-linux-gnueabi root@(none):~# |
Page 1 of 1 | All times are UTC-06:00 |
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |